![Midweight Hammer Forged Barrel, Midlength 16in and 14.5in Midweight Hammer Forged Barrel, Midlength 16in and 14.5in](https://cdn11.bigcommerce.com/s-ua6zvruewu/images/stencil/300x300/products/240/990/HFB-MW-ML-16-14-sidebyside__05595.1610657631.jpg?c=1)
Lightweight Hammer Forged Barrel, Midlength, .750 Gas Journal w/alignment notch for use with our TABBED gas blocks (non-tabbed gas blocks will still work.)
In-house pinned gas block is a tabbed,"ultra low profile", pin-only, gas block with no need for set screws, and has no threaded holes for them. We now use a heavy duty, double coiled spring pin which can be driven in/out in either direction, instead of the old taper pin.
Cold Hammer Forged Barrels
Hammer forging is a process in which a drilled, reamed and honed blank has the rifling formed into it by placing the barrel blank on a mandrel that has the rifling ground into its outer surface. The blank and mandrel are then placed between two opposing power hammers and the blank is beaten around the mandrel leaving the rifling pattern in the barrel. This process leaves an extremely smooth and consistent surface on the inside of the barrel, that lends itself to excellent accuracy. The forging process also work hardens the barrel steel causing a very durable and much longer lasting barrel. Our barrels have a slight taper to the bore during the hammer forging process to ensure better accuracy.
Chrome lined chamber and bore
The hard chrome used to coat the chamber and bore are harder than the barrel steel itself. This aids in longevity and also reduces fouling and corrosion often seen in austere field conditions. Chrome also aids in chambering, extraction, and overall reliability of the weapon. Thus, giving the operator a more reliable weapon with less maintenance. We have our chrome lining applied to twice the thickness of standard small arms barrels.
Barrel steel
The steel used in our hammer forged barrels was specifically developed as machine gun barrel steel to help increase the barrel life under prolonged rigorous firing schedules.
Twist rate
We use a 1/7 (1 turn in 7 inches) twist rate in all our barrels. This is the best overall twist rate for this weapons system. The 1/7 twist will stabilize any of the light weight 5.56 bullets as well as any other twist. This twist will also stabilize the newer heavier bullets that are being used allowing the operator to get the best performance out of this weapon system.
Chamber
We use a true 5.56 chamber in our barrels allowing the operator the ability to use the higher pressure military ammunition on the market and helping to enhance reliability.
Feed ramps
Our barrels are supplied with extended M4 style feed ramps to enhance overall feeding and weapons reliability.
Finish
The barrel finish we use is a manganese phosphate finish (Mil-Spec A-A-59267). This finish allows for better absorption of oils to help prevent corrosion. These barrels are all finished prior to any gas blocks being mounted to ensure the entire surface is covered to maximum protection even under the gas block.
HPT/MP inspected
HPT(high pressure test) is a process where a proof load rated at 70,000 psi, far exceeding a normal round, is fired trough the barrel then the barrel is MPI (Magnetic Particle Inspected) to detect any flaws in the barrel steel from the proof load. These are standard quality assurance tests performed on all our hammer forged barrels to ensure the highest quality product.
Weight
16in Midlength 1lb 10.4oz stripped
14.5in Midlength 1lb 8oz stripped
13.9in Midlength 1lb 7oz stripped
Gas Port Size
16in .075
14.5in .074
13.9in .074
*****Centurion Arms barrels require no further break in*****
*** We recommend gunsmith installation for all of our parts. We cannot warranty items damaged by improper installation.
Picked this barrel up for a new upper build. Definitely a good battle rifle barrel. Have shot several hundred rounds through it already and it is very accurate.
Picked up one these barrels for my SBR and it has been fantastic. During sight-in after upper assembly, I put 5 shots of match ammo into .25" at 50 yards. I currently have about 3k rounds through the barrel (4 carbine classes, 2-gun matches, plinking) and it still shoots .75 MOA.